1、选用的电机功率N=(Q/3600)*P/(1000*η)*K其中风量Q单位为m3/h,全压P单位为Pa,功率N单位为kW,η风机全压效率(按风机相关标准,全压效率不得低于0.7,实际估算效率可取小些,也可以取0.6,小风机取小值,大风机取大值), K为电机容量系数,参见下表。
2、功率=流量X压力/1000/3600/效率。除1000是让功率变为KW,除3600是让每小时流量变为每秒的。风机选型确定了,的确是压力越高流量应该越小,这点可以从风机的性能曲线上看出。相同的风机可以满足很多流量压力,但是每个点所需的功率并不完全相同,这从功率的公式可以看出。
3、风量=(功率*3600*风机效率*机械传动效率*1000)/风压。风机效率可取0.719至0.8;机械传动效率对于三角带传动取0.95,对于联轴器传动取0.98。
4、已知风机的风量和压力,怎么计算所需电机功率? N={PQ/(1000η1×3600η2)}×KN-功率(kw);P-风压(Pa);Q-风量(m3/h);η1-风机效率(74-81%);η2-机械效率(95-98%);K-电机容量储备系数(5-15)。对于3kw以下的电机,K值可取5;以上K值可取15。
5、n:转速 N:功率 P:压力 Q:流量 Q1/Q2=n1/n2 P1/P2=(n1/n2)平方 N1/N2=(n1/n2)立方 风机风量及全压计算方法风机 功率(W)=风量(L/S)*风压(Kpa)/效率(75%)/力率(75%)全压=静压+动压。
应该是可以的。20kw电机的定子没有通电的情况下,转子不会励磁,因此,没有电磁阻力,只相当于20kw的电机带动一个没有负荷的转子在转动,消耗的功率很小,如果实测功率的话,最多0.3kw。但是,如果20kw电机通电的话,问题就变得复杂了。
能带约120平米的冷库。用多大压缩机除了与面积大小有关,还与温度有关。一般冷库压缩机制冷量和面积参照:一匹=2200-2600W,适用面积12-18平米25立方米。5匹=3200-3600W,适用面积15-24平米。2匹=4500-5500W,适用面积22-31平米。
要使用25平方的线。对于20千瓦的电机,根据功率计算,单相电机的电流大约为90A。而25平方铜芯线的安全载流量为120A,可以满足电机的电流负荷要求。为了确保电线能够承受电机的功率和电流负荷,选择25平方的线是合适的选择。
如果你使用的电机是三相电机,则20千瓦电动机电流大概是2*20=40A,用一般铜芯动力电缆的话,每mm^2的电缆能载流5A,故需要使用10mm^2的铜芯动力电缆较为保险。如果你使用的电机是单相电机,则20KW的工作电流为90A,则应该配用截面积35平方毫米的铜芯线。
ov电压总功率是112千瓦,电流500A,240的铜芯电线。
一般四千瓦环保空调是4匹的空调,制冷面积在30-50平方米左右,大概长一米七八左右宽占地在一平方米左右。
当然,超负荷增加室内机,使得室外机无法正常承担交换工作,只好连续不断的运行,这时,室外机耗电处于“饱和”状态,增加再多的室内机,只能使效率更低,外机的耗电是不会增加多少了。水机和冷媒机在其他方面也有区别,舒适度上,水机空调比冷媒机舒适,原因是风量大温差小。
台28 千瓦的水泵,其中一台备用,则按4 × 28=112 千瓦计算电流负荷为168 安。 估出电流负荷后,可根据它选择送电给这个车间的导线规格及截面。 这口诀对于其它工厂的车间也适用。其它生产性质的工厂大多是长期运转设备, 一般可按“其余1 5 0 ”的情况计算。
电流知道了,就可以根据电流值来查表选择线径了,给你个网址《导线安全载流量表》:http://wenku.baidu.com/view/ebfbe18202d276a200292ece.html 然后,根据公式:P=根号3*U*I*功率因数(一般来说选0.85好了)=732*0.4*190*0.85=112KW。
通常我们是通过风量、风压来选型风机的大小...就是这样的风量、风压需要多大的轴功率来满足!轴功率才是真正的耗电量!需要的风机轴功率以及对应的电机大小!并不是电机来选择风机的风量、风压。
1、低静压机组的额定风量是机外余压为0Pa时的值,在不带风口和过滤器的余压值为12Pa。供冷工况参数:进口空气干球温度27℃,湿球温度15℃,进水温度7℃,水温差5℃。供热工况参数:进口空气干球温度21℃,进水温度60℃,热水流量同供冷工况。上述表格中性能参数如有更改,恕不另行通知。
2、而与普通的风机盘管不同的是,卡式风机盘管具有外观时尚大方,通风噪音极小,提供的空气和风量更加舒适的优点,今天小编就给大家介绍卡式明装风机盘管机组的详细性能参数。
3、FP-1200是一种风机盘管的型号,风量和电机功率的具体参数取决于不同的型号和配置。一般来说,FP-1200的风量应该在1000-1500立方米/小时之间,而电机功率则应该在100-200瓦之间。但是具体参数还需要参考该型号的说明书或者咨询售后服务人员以获取准确信息。
4、型号:FP-KM34 品牌:江瀚 电流:0.2(A)电压:220(V)功率:60(w)风量:2600 适用风机:广泛 额定供冷量:3600 额定供热量:5900 看完这些价格信息之后,小编总结了一下,卡式风机盘管的价格应该大致在300到1000块钱这个价格区间,不过这只是网上的信息,可以参考一下。
5、附表格加以说明:FP系列风机盘管性能参数表 风机盘管管内流过冷冻水或热水时与管外空气换热,使空气被冷却,除湿或加热来调节室内的空气参数。它是常用的供冷、供热末端装置。
6、这种叫风机盘管,里面用电不见就是风机电机,一般30W至250W之间。下面是某品牌风机盘管技术参数:某品牌风机盘管技术参数 关于风机盘管的选择:家用一般选择标准型,这类风机盘管功率一般不超过100W。家用的,建议选择两排管,主要噪音较低。水系统中央空调,舒适性较多联机(一拖多)的好。
1、大约15300立方米每小时的风量。5千瓦风机可以产生大约15300立方米每小时的风量。主要依据是风机的功率(5千瓦)和风机的效率(一般在0.4左右),通过功率和效率的乘积可以估算出风机的风量。
2、千瓦冷风机风量25000。根据查询相关公开信息显示,冷风机不同型号的风机风量相差很大,5千瓦冷风机风是轴流风机,8号机座的轴流风机配功率5千瓦的电机风量是25000。
3、首先,该风机的型号为DTBF-250-A/5KW,这意味着它是一款功率强大的设备,额定功率达到了5千瓦。其主要运行特性之一是转速,可以达到3200转每分钟,这意味着它具有高效的空气处理能力。